- Microfluidics M-700 Microfluidizer Processor Production Scale Homogenizer (7115-10) 10,000 psi - H10Z-18 Interaction Chamber (IXC) - T260Z Auxiliary Processing Module (APM) - Start/Stop Motor Control Box - Explosion Protected Electrical - High Pressure Plunger Seals and Check Valves - Single Plunger - Efficient Electric/Hydraulic Drive System - Maintenance Toolkit/Spare Parts - Heat Exchanger Option* - 90-Day Warranty
Notice: This system requires appropriate power and air supply for operation. Please make sure your facility is equipped with the necessary power and air supply before purchasing.
*Notice: Plumbing for the heat exchanger option is not included and must be acquired separately to utilize the option.
Not Included:
- Diaphragm Pump
Notice: This homogenizer does not come with a diaphragm pump. We can provide a diaphragm pump for an additional cost.
Fully Tested and Working Without Issue:
After its initial disinfection and inspection, our technicians tested the Microfluidics M700 microfluidizer processor with the following results:
- Inspected and cleaned liquid (product) end: PASSED - Ran and sterilized with 15 liter of isopropyl alcohol: PASSED - Product flowrate at 4.2 lpm at 10,000 psi: PASSED - Verify highest pressure ran of 10,000 psi: PASSED - Check process pressure control valve: PASSED - Check motor start/stop control: PASSED - Check pressurized air inlet assembly: PASSED - Check hydraulic oil heat exchanger: PASSED - Check/replace plunger seal assembly: PASSED - Clean and inspect plunger: PASSED - Clean and inspect bearing isolate/O-rings: PASSED - Clean and inspect/replace high pressure fittings: PASSED - Clean and inspect/replace inlet check valve: PASSED - Clean and inspect/replace priming valve: PASSED - Check/replace hydraulic oil and filter: PASSED - Clean the hydraulic oil reservoir: PASSED - Clean hydraulic oil suction strainer: PASSED - Inspect/replace hydraulic cylinder seals: PASSED - Inspect/replace pneumatic switches: PASSED - Backflush interaction chamber: PASSED
Notice: This homogenizer has only 23,159 strokes which is about 15.4 hours of runtime.
Specifications:
Manufacturer
Microfluidics
Type
M700 Series
Model No.
7115-10
Serial No.
2006171
Mfg. date
2006
Pressure range
Up to 10,000 psi (690 bar)
Flowrate at 25 strokes/min at 10,000 psi
~1.24 gpm (4.74 lpm)
Feed temperature
Maximum 165°F (75°C)
Utility requirements
Cooling water for hydraulic oil heat exchanger and process fluid heat exchanger, compressed air for feed pump and cycling control switches requires (50-150 psi 1 scfm@ 50 psi, pressure dew point of 0-35°F)
Power rating
3 phase electrical service, 208/230/380/460/575V 15 HP (11.1 kW)
Dimensions (W x D x H)
~62 x 42 x 57 in
Weight
~1,500 lb (680 kg)
Estimate Shipping
Microfluidics M700 Microfluidizer Processor 7115-10 Production Scale Homogenizer
You Will Receive:
- Microfluidics M-700 Microfluidizer Processor Production Scale Homogenizer (7115-10) 10,000 psi - H10Z-18 Interaction Chamber (IXC) - T260Z Auxiliary Processing Module (APM) - Start/Stop Motor Control Box - Explosion Protected Electrical - High Pressure Plunger Seals and Check Valves - Single Plunger - Efficient Electric/Hydraulic Drive System - Maintenance Toolkit/Spare Parts - Heat Exchanger Option* - 90-Day Warranty
Notice: This system requires appropriate power and air supply for operation. Please make sure your facility is equipped with the necessary power and air supply before purchasing.
*Notice: Plumbing for the heat exchanger option is not included and must be acquired separately to utilize the option.
Not Included:
- Diaphragm Pump
Notice: This homogenizer does not come with a diaphragm pump. We can provide a diaphragm pump for an additional cost.
Fully Tested and Working Without Issue:
After its initial disinfection and inspection, our technicians tested the Microfluidics M700 microfluidizer processor with the following results:
- Inspected and cleaned liquid (product) end: PASSED - Ran and sterilized with 15 liter of isopropyl alcohol: PASSED - Product flowrate at 4.2 lpm at 10,000 psi: PASSED - Verify highest pressure ran of 10,000 psi: PASSED - Check process pressure control valve: PASSED - Check motor start/stop control: PASSED - Check pressurized air inlet assembly: PASSED - Check hydraulic oil heat exchanger: PASSED - Check/replace plunger seal assembly: PASSED - Clean and inspect plunger: PASSED - Clean and inspect bearing isolate/O-rings: PASSED - Clean and inspect/replace high pressure fittings: PASSED - Clean and inspect/replace inlet check valve: PASSED - Clean and inspect/replace priming valve: PASSED - Check/replace hydraulic oil and filter: PASSED - Clean the hydraulic oil reservoir: PASSED - Clean hydraulic oil suction strainer: PASSED - Inspect/replace hydraulic cylinder seals: PASSED - Inspect/replace pneumatic switches: PASSED - Backflush interaction chamber: PASSED
Notice: This homogenizer has only 23,159 strokes which is about 15.4 hours of runtime.
Specifications:
Manufacturer
Microfluidics
Type
M700 Series
Model No.
7115-10
Serial No.
2006171
Mfg. date
2006
Pressure range
Up to 10,000 psi (690 bar)
Flowrate at 25 strokes/min at 10,000 psi
~1.24 gpm (4.74 lpm)
Feed temperature
Maximum 165°F (75°C)
Utility requirements
Cooling water for hydraulic oil heat exchanger and process fluid heat exchanger, compressed air for feed pump and cycling control switches requires (50-150 psi 1 scfm@ 50 psi, pressure dew point of 0-35°F)
Power rating
3 phase electrical service, 208/230/380/460/575V 15 HP (11.1 kW)
Dimensions (W x D x H)
~62 x 42 x 57 in
Weight
~1,500 lb (680 kg)
WE SHIP WORLDWIDE
Many of our international orders have custom-built wooden crates to fully enclose them during shipping.
